Recent Activity

Activity stream for all registered members at GeoExchange® Forum.

  1. docjenser replied to the thread Looking for design advice on equipment install..

    You have radiant in your garage but not radiant in the house? Must be a car lover:D Kidding aside, many ways to skin a cat. Not sure if...

    Nov 12, 2019 at 12:34 AM

  2. mrpac replied to the thread Sharkbite fitting for desuperheater.

    My system is plumbed in with shark bites and PEX. No issues to date, 10yrs old!

    Nov 11, 2019 at 10:08 PM

  3. mtrentw replied to the thread Looking for design advice on equipment install..

    I would definitely want to keep all 5 loops together. That would ensure you're not overburdening one set and that each unit would have...

    Nov 11, 2019 at 1:25 PM

  4. Alexander Wood replied to the thread Why No High End Split Geo Equipment?.

    Nice! That would really be a game changer in geo retrofits.

    Nov 10, 2019 at 8:14 PM

  5. OakStreetDesign attached a file to the thread Looking for design advice on equipment install..

    I also have PEX installed in my garage slab so if there is a way to incorporate heat there in the design I would like to consider it....

    IMG_0864.JPG Nov 10, 2019 at 10:27 AM

  6. OakStreetDesign posted a new thread.

    Looking for design advice on equipment install.

    Hello all, noob here looking for a little help. I'm a builder of nearly 30 years but a novice on geothermal. Currently building my own...

    IMG_2493.JPG IMG_2512.JPG IMG_2517.JPG

    Forum: General Discussions

    Nov 10, 2019 at 10:04 AM

  7. samangogo posted a new thread.

    TXV PART

    I had a high pressure red light in July 2019. Tech came out and replaced txv , $515 bill and all was well. Had red low pressure light in...

    Forum: General Discussions

    Nov 9, 2019 at 5:52 AM

  8. mtrentw replied to the thread Sharkbite fitting for desuperheater.

    IIRC, SharkBite fittings are rated to 200 degrees F and 200 psi. I'd feel safer with those than a sweat fitting if you are just...

    Nov 8, 2019 at 2:23 AM

  9. Colton Weber replied to the thread Sharkbite fitting for desuperheater.

    Ah ok. I had seen other posts of people using them thats why I was wondering. I will have to figure out how to sweat pipes then

    Nov 7, 2019 at 6:35 PM

  10. SShaw replied to the thread Sharkbite fitting for desuperheater.

    I heard copper is recommended to connect the DSH to the buffer tank, to avoid the possibility of PEX rupturing if something fails and...

    Nov 7, 2019 at 6:21 PM

  11. Colton Weber posted a new thread.

    Sharkbite fitting for desuperheater

    Finally getting around to hooking jp my holding tank to my desuperheater. I believe I read in the instructions that waterfurnace does...

    Forum: General Discussions

    Nov 7, 2019 at 5:24 PM

  12. viveksunderam replied to the thread Why No High End Split Geo Equipment?.

    I heard from an installer that they had an event where they showed a demonstration unit this summer, and told the installer that the...

    Nov 7, 2019 at 2:23 PM

  13. Stickman attached a file to the thread Pennsylvania Monitoring systems.

    Are you looking to see what the water temps are at the moment you look at the device, historical (logging) data, or the delta? I think...

    upload_2019-11-7_6-21-19.png Nov 7, 2019 at 6:22 AM

  14. SShaw replied to the thread Pennsylvania Monitoring systems.

    I have a Waterfurnace 7 series with the performance monitoring kit. The kit requires the Aurora Expansion Board (AXB) to operate and...

    Nov 6, 2019 at 3:00 PM

  15. Kenstone replied to the thread Pennsylvania Monitoring systems.

    After doing some digging it looks like Waterfurnace's Performance Monitoring Kit 5SPKL unit sizes 030–072 would work it would just be a...

    Nov 6, 2019 at 1:54 PM
Show older items
Loading...